Description
PFX-32 : 32 Way 5A Programmable Dimmer MCB
Features:
-
-
- All digital control – each PFX dimmer contains the latest generation controller and hard-fired digital dimmer circuits
- Programmable scenes (20 per area standard, expandable to 120 with Home-Icon)
- 3 phase dimming or switching
- 4 selectable dimming curves
- Each channel can be set to be a switching only (non-dimming) circuit
- 1024 step fade resolution for all fade and cross-fade functions
- Variable fade rates from 0.5 seconds to 2 hours (to gradually turn lights on/off)
- 4 data buses including:
- X bus
- RS485
- RS232
- DMX (option)
- No minimum load on any channel
- Multi-zoning 256 zones in one local area
- 15 room multi-partition control
- Mains voltage compensation
- Voltage stabilization
- 24-hr 7-day built-in event timer (battery backed)
- Occupancy detection
- Daylight balancing
- Low noise operation – audible noise from a 16 channel 10A dimmer fully loaded at 50% is less than 30db @ 1m
- Energy saving – efficiency <98%
- Programming and operation from:
- remote control handset, infra-red
- PC laptop
- Futronix Home-Icon® TFT Color Touch Screen Controller
- Permanent memory – in the event of a power blackout pre-set scenes are not lost and re-programming of dimmer is not necessary
- Temporary circuit adjustment without save
- Master raise and lower
- Exit Delay & Sleep Timer
- Security settings
- Virtual I/O for control of:
- non-lighting equipment
- audio and video equipment
- curtains, shades, blinds
- water features
- security and alarm systems, etc.
- Direct control of AV systems
- Electrician-friendly installation
-
PFX System Dimming Racks Compatible with Home-Icon:
|
Type
|
Channels
|
Load
|
dimension
Height, Width, Depth |
Phase
|
|
PFX-32
|
32
|
5A
|
980 X 980 X 150mm
|
1 phase
|
|
PFX-16
|
16
|
10A
|
950 X 500 X 110mm
|
3 phase
|
|
PFX-12
|
12
|
10A
|
950 X 500 X 110mm
|
3 phase
|
PFX System – Technical Specifications:
|
Mains Supply Input
|
380-415V ac @ 50/60Hz three phase
270V ac @ 60Hz 200-240V ac @ 50/60Hz single or three phase 110-130V ac @ 50/60Hz single phase |
|
Dimming Output (no minimum load)
|
5, 10, 20 or 40A per channel continuous tungsten, low voltage, halogen, neon/cold cathode, and fluorescent (high frequency)
|
|
Dimming Output (0-10Volt Optional)
|
LED transformers & fluorescent regulation ballasts
|
|
DMX
|
Control for colour changing lamps/LEDs & accessories
|
|
Switching Output
|
5, 10, 20 or 40A per channel continuous HID, non-dim fluorescent, other loads
|
|
Dimming Unit
|
Output devices rated at 40A 1000V peak
|
|
Interference Suppression
|
Heavy duty, high inductance chokes 200uS rise time 1.4 mH
|
|
Cable Termination (incoming)
|
200A single or three phase switch disconnector
|
|
Protection
|
MCB 10A, 20A or 40A type B or C
|
|
Cable Entry – Power
|
Bottom of chassis 3 x 51mm + 5 x 25mm
|
|
Cable Entry – Control
|
Left side of chassis 20mm + 12mm
|
|
Ambient Temperature
|
40ºC maximum, generously rated heatsinks limit internal temperature rise to less than 25°C above ambient temperature
|
|
Network
|
X-bus protocol network switch panel bus, BMS, PC network, RS485, RS232
|
|
Approvals
|
Conforms to relevant UL, BS & EN safety standards; CE approval
|
I-Phone Connectivity
Use your iPhone or iPod touch to take control of Futronix dimmers and other home electronics devices. Your choice of scenes can be selected from the menus or automatically using one key MACRO commands. Eliminate that cluttered mess of remotes, by consolidating all your remotes into one single i-Phone application. Select your favorite lighting scenes, close the blinds, power up the surround sound system, turn up the volume and flip through channels using one of these Futronix compatible devices.
